| Type |
Product |
Description |
| DIE RELEASE |
LUBRICAST 899 |
45% Solids, semi-synthetic with three super high performance polymers that range from 200°F to 800°F. It is formulated for the aluminum, magnesium or zinc die caster with large or small complex molds. Lubricast 899 forms a micro-stable emulsion in both hard and soft water. Recommend ratios from 30:1 to 300:1. Cast parts can be painted or plated without concern for lack of adhesion. This product will enhance casting quality and will reduce cycle times. |
 |
| DIE RELEASE |
LUBRICAST 840 D |
47% solids, semi-synthetic with three different high performance polymers that range from 200°F to 800°F. Formulated for aluminum, magnesium or zinc. Recommend ratios from 30:1 to 200:1.
|
| DIE RELEASE |
LUBRICAST 820 D |
LUBRICAST 820 D 21% solids, semi-synthetic with three different high performance polymers that range from 200°F to 800°F. Formulated for aluminum, magnesium or zinc. Recommended ratios from 20:1 to 100:1. |
|
| DIE RELEASE |
LUBRICAST 814 ZR |
LUBRICAST 814 is a light to medium duty die release agent for use on zinc die casting operations. This micro emulsion was specifically formulated to eliminate buildup and ensure dimensional stability. In addition, the bright clean finish enables parts to be paint able or plated. LUBRICAST 814 is easily mixed in water and can be diluted from 50:1 to 100:1 ratios. It is easily applied with hand held or automatic spray systems. This tightly bonded micro emulsion will not clog spray nozzles and is easily cleaned up. |
| DIE RELEASE |
LUBRICAST 898 NS |
LUBRICAST 898 NS is a high performance non-silicone die release agent. It is formulated for the aluminum and zinc die caster with complex or detailed molds. LUBRICAST 898NS forms a micro-stable solution in both hard and soft water and may be used in fully automatic spray systems or hand-held units. LUBRICAST 898NS is extremely resistant to rancidity and can be diluted up to 20:1 to 100:1 with water. This new Chemtool Incorporated technology has had an extremely successful history of producing high volume castings weighing over 50 pounds. |
| DIE RELEASE |
LUBRICAST 935 |
Is a high performance die release agent that can be diluted out to 120 to 1. The product is formulated for the aluminum, magnesium or zinc die caster with large of small complex molds. Lubricast 935 forms a micro-stable emulsion in both hard and soft water.
|
| START-UP/SOLDER REMOVAL |
LUBRICAST HI TEMP |
Can also be used as a high performance start-up release by applying a thin coat with a pump spray bottle. When using the Lubricast Hi Temp as a start-up release it is recommended to be used in neat form or 1:1 ratio. Lubricast Hi Temp can also be used as an anti-solder removal spray easily applied by pump spray bottle directly to the solder area in net form. |
| START-UP/SOLDER REMOVAL |
LUBRICAST 628 |
A complex blend of paraffin based solvents that are designed to coat a protective layer on the mold surface for cold start-ups. Lubricast 628 is also designed to aid the removal of stuck castings by applying the Lubricast 628 to the outer edge of stuck castings. The complex blends of polymers are designed to wick and apply a protective layer between the casting and mold for gentle removal of the casting. Lubricast 628 can be applied by brush or spray. |
START-UP/SOLDER REMOVAL
|
DIKOTE 1212 |
Dikote 1212, also known as anti-solder paste, is a complex blend of organic waxes and high temperature lubricity additives. Dikote 1212 is primarily used in the event that excessive solder build-up occurs on the casting mold and can also be used as a start-up aid. Dikote 1212 is a thick paste that can be applied by a stiff bristle brush. |
| START-UP/SOLDER REMOVAL |
LUBRICAST Bee's Wax |
A solid 3" wide by 4" long 1?" thick block of Bee's Wax designed to aid the removal of stuck castings by first applying heat to the surrounding area of the mold and the stuck casting. By pressing the Lubricast Bee's Wax to the outer edge of stuck castings in the pre heated area the Bee's Wax will wick and apply a protective layer between the casting and mold for gentle removal of the casting. |
| TIP/PLUNGER LUBES |
LUBRICAST 14 |
A 9,000 SUS viscosity @ 100°F, water washable semi-fluid with high temperature lubricity additives. Can be applied by drip, brush or by internal sleeve high-pressure methods. |
| TIP/PLUNGER LUBES |
LUBRICAST 28 |
A heavy duty, high viscosity product. It is an oil-based product that incorporates high temperature lubricity additives. This combination provides the wetting, film strength and maximum protection required for the plunger tips and shot sleeves.
|
| TIP/PLUNGER LUBES |
LUBRICAST 677 WS |
38% solids, semi-synthetic, non-graphite water soluble, with high temperature lubricity additives. Ratios from neat up to 6:1. Can be applied directly into the shot chamber through the pour hole, drip, brush or by internal sleeve high-pressure methods. |
| TIP/PLUNGER SHOT BEADS |
LUBRICAST PROSHOT 429 |
A 4 to 9 mesh size graphite coated solid wax based lubricant with extreme pressure and boundary lubricants. Designed to be dispensed into the cold chamber prior to metal pour. |
| QUENCHING/ TRIMMING FLUIDS |
CT 500-LC |
46% solids, true solution, oil rejecting synthetic designed with rust preventives for trim dies and quench tanks. CT 500-LC offers maximum heat transfer and corrosion protection of aluminum and zinc castings at 2%. Designed with high performance lubricity additives for trimming operations, CT 500-LC can be used at 5%. |
| QUENCHING/ TRIMMING FLUIDS |
CT 250-NC |
General-purpose soluble oil designed with rust preventives for trim dies and quenching tanks. CT 250-NC offers maximum heat transfer and corrosion protection of aluminum and zinc castings at 4%. Designed with a high performance lubricity additive for the trim die operation at 7%. |
| TRIMMING FLUIDS |
CT 3430 |
Vanishing oil used to trim aluminum and zinc casting. CT 3430 has a light lubricating oil that helps lubricate the trim die's functional components. CT 3430 also has a solvent carrier that helps eliminate cleaning when solvent carrier evaporates. CT 3430 is to be used in neat form and has a flash point of 120°F. |
| HEAT TRANSFER FLUIDS |
CT 400 HTO |
A premium heat transfer liquid that is used to cool and heat casting molds. Provides oxidation and thermal stability in vented systems at continuous temperatures up to 600°F. |
| HEAT TRANSFER FLUIDS |
CT 500 HTO |
Is the same as the CT 400 HTO but has a premium oxidation and thermal stability package that provides less maintenance and longer sump life. |
| FIRE RESISTANT HYDRAULIC FLUIDS |
LUBRICAST 902-LPC |
A 200 SUS viscosity at 100°F Factory Mutual approved water glycol fire resistant hydraulic fluid, with an ideal operating temperature range 100°F to 120°F maximum continuous 130°F to 140°F, maximum spike 150°F. Typical operating pressure 2000 PSI to 3000 PSI withstanding spike of 5000 PSI. ASTM D 2882 Vickers pump test total wear of less than 25 mg. |
| FIRE RESISTANT HYDRAULIC ADDITIVES |
CT 324-CI |
A Lubricast 902-LPC water and morpholine based additive. Used to increase reserve alkalinity, in order to maintain corrosion protection levels of water glycol products. |
| FIRE RESISTANT HYDRAULIC ADDITIVES |
CT 910-C |
A 960 SUS water glycol hydraulic fluid concentrate additive used to increase the viscosity of hydraulic systems containing Lubricast 902-LPC. Note: Typical reason for low viscosity is due to excessive water being introduced to the hydraulic system. |
